Jenn-Air Refrigerator Water Filter | How to Choose the Right One, Replace It, and Reset the Light
A Jenn-Air refrigerator water filter helps keep your drinking water and ice tasting fresh by reducing common contaminants. When the filter is overdue, you’ll often notice it first in the taste, the smell, or a slower water flow.
This guide walks you through picking the right filter, finding where it goes, replacing it without a mess, and resetting the filter light so you can order with confidence and get back to clean water fast.
Check list:
- Find the right filter by checking the model printed on your old filter or using a model-number filter finder.
- Replace about every 6 months (or sooner if your water flow drops).
- Reset the filter light (many Jenn-Air models reset by holding MAX COOL + MAX ICE for 3 seconds).
When should you replace a Jenn-Air water filter?
Most homes do best replacing the filter every 6 months (or around 200 gallons, depending on use).
Replace it sooner if you notice:
- Water comes out slower than usual
- Water tastes “flat,” metallic, or has an odor
- Ice tastes off
- The “replace filter” light turns on
If you have hard water or use a lot of ice, you may hit that replacement window earlier.
How to choose the correct Jenn-Air refrigerator water filter
The easiest way to avoid wrong orders is to match the filter the fridge already uses.
Option 1: Check the old filter
Remove the current filter and look for the part number printed on it. This is the most reliable method.
Option 2: Use a model-number filter finder
If you can’t read the label (or the filter is missing), use a filter finder and enter your refrigerator model number..
Popular Jenn-Air compatible filter option
Jenn-Air lists multiple everydrop filters as compatible with Jenn-Air refrigerators. Always confirm fit by your model number, but these are common options shoppers look for:
| Filter | Also known as | Best for |
| everydrop® Filter 4 (EDR4RXD1) | “Filter 4” | Fridges that specify Filter 4 compatibility |
| everydrop® Filter 2 (EDR2RXD1) | “Filter 2” | Fridges that specify Filter 2 compatibility |
Check Filter 4 and Filter 2 here.
Where is the water filter located on a Jenn-Air refrigerator?
The filter location depends on the refrigerator style, but it’s usually in one of two places:
- Inside the refrigerator compartment (often near the top area)
- In the base grille near the bottom front on some models
If you don’t see it inside the fridge, check the bottom grille—many people miss it the first time.
How to replace a Jenn-Air refrigerator water filter
Most replacements take about 5–10 minutes.
- Get a towel ready. A small drip is normal.
- Remove the old filter.
- Twist style: turn to unlock, then pull out
- Push/release style: press the release button (or push in to release), then pull out
Install the new filter.
- Remove any protective caps
- Push the filter in firmly until fully seated
- Twist/lock if your model uses a twist mechanism
Flush the filter.
Run water for a few minutes to clear air and carbon fines (tiny harmless particles). Your dispenser may sputter briefly—this is normal right after a change.
How to reset the Jenn-Air water filter light
After installing the new filter, reset the indicator so your fridge can track the next replacement.
On many Jenn-Air full-size refrigerators:
- Touch and hold MAX COOL and MAX ICE together for 3 seconds to reset the water filter status.
You may see a short countdown on the display during the reset.
If the light won’t reset, Jenn-Air’s troubleshooting guidance commonly points to using the same button combo again and ensuring the filter is installed correctly.
7 Common Mistakes
These are the most common issues that lead to leaks, bad taste, or a filter light that won’t clear:
- Buying a filter because it “looks the same” (fit varies by model)
- Not seating the new filter fully (it must click/lock into place)
- Forgetting to remove the protective caps
- Skipping the flush, then thinking the new filter “tastes weird”
- Not resetting the filter status light
- Pulling too hard on a stuck filter, especially in base-grille locations
- Waiting too long past 6 months, especially in high-use homes
More Update Frigidaire Genuine PureAir Refrigerator Air Filter RAF-2 / AF-2 (FRGPAAF2)
FAQ
How often should I replace my Jenn-Air refrigerator water filter?
Most users replace it every 6 months (or about 200 gallons).
How do I reset the Jenn-Air filter light?
Many Jenn-Air models reset by holding MAX COOL + MAX ICE for 3 seconds.
Where is the water filter located in a Jenn-Air refrigerator?
Common locations are inside the fridge or in the base grille at the bottom front.
What if the filter status light won’t reset?
Re-seat the filter (remove and reinstall firmly) and try the reset again.
